Numerical Study on Effects of Design Parameters of Seven-Bladed Propeller with Skew on Its Cavitation Performance

doi:10.13675/j.cnki. tjjs. 190009

Journal of Propulsion Technology ›› 2019, Vol. 40 ›› Issue (10): 2366-2372.DOI: 10.13675/j.cnki. tjjs. 190009

• Ship Propulsion • Previous Articles Next Articles

Numerical Study on Effects of Design Parameters of Seven-Bladed Propeller with Skew on Its Cavitation Performance

Wuhan Second Ship Design and Research Institute，Wuhan 430064,China

Published:2021-08-15

七叶侧斜螺旋桨设计参数对空泡性能的影响研究

齐江辉¹,郭健¹,郑亚雄¹,郭翔¹,陈强¹

武汉第二船舶设计研究所

基金资助:
国家能源应用技术研究及示范工程项目 NY20150201国家能源应用技术研究及示范工程项目（NY20150201）。

Abstract

Abstract: In order to establish an effective method to predict cavitation characteristics of the seven-bladed propeller, the CFD method is adopted to predict unsteady cavitation on marine propeller in full wetted flow and cavitation flow. Then the effects of parameters of the propeller on its cavitation performance is analyzeed. The validation studies of the DTMB4381 propeller for unsteady cavitation flow are presented, and the calculation results are in acceptable agreement with the experimental results and observations. Through mesh convergence analysis, the convergency of the mesh is completed thus guarante the accuracy of calculation. Parameterization of the marine propeller is performed with the B splines for skew, chord and rake distributions. The effects of some parameters such as skew, chord and rake distributions on the seven-bladed propeller with skew cavitation performance are studied. The results show that with the skews increasing, the cavity enxtent will decrease and the cavitation boundary in side will shift to the centerline of the blade and the average thrust increased by 9.0% relative to the prototype. The cavity extent will increase and the average load per unit area of the propeller will decrease with the areo ratio increasing and the average thrust increased by 11.8% compared to the original propeller. The calculation of the rake distribution curvature to pressure side and suction side indicates that a certain degree of rake is benefical to improve the cavitation performance of marine propeller.

Key words: Propeller;Cavitation;B spline;Unsteady flow;Parameter optimization

摘要： 为建立有效的预报螺旋桨空泡性能的方法，并基于该方法参数化分析七叶侧斜螺旋桨设计参数对空泡性能的影响，基于CFD方法建立了螺旋桨全湿流和空泡流非定常数值计算模型。通过对DTMB4381标准螺旋桨全湿流及空泡数值模拟结果与试验值的对比，验证了计算模型的准确性。通过对网格的收敛性分析，验证了收敛性并保证了计算精度。采用B样条曲线拟合方法拟合某七叶侧斜螺旋桨设计参数，通过改变控制点的值改变设计参数的分布型式。在此基础上重点分析了该七叶侧斜螺旋桨桨叶侧斜、弦长以及纵倾分布型式对螺旋桨空泡性能的影响，计算表明加大侧斜能够减小空泡面积，使空泡的随边边界向桨叶中心偏移,增大侧斜后螺旋桨平均推力较原型桨增大9.0%；增加盘面比会使空泡面积增大，但会降低螺旋桨单位面积的平均负载，增加盘面比后螺旋桨平均推力较原型桨增大11.8%；同时桨叶向压力面弯曲或向吸力面弯曲的计算都表明，一定程度的纵倾有利于改善螺旋桨的空泡性能。

关键词: 螺旋桨;空化;B样条，非定常流;参数优化

QI Jiang-hui¹,GUO Jian¹,ZHENG Ya-xiong¹,GUO Xiang¹,CHEN Qiang¹. Numerical Study on Effects of Design Parameters of Seven-Bladed Propeller with Skew on Its Cavitation Performance[J]. Journal of Propulsion Technology, 2019, 40(10): 2366-2372.

齐江辉,郭健,郑亚雄,郭翔,陈强. 七叶侧斜螺旋桨设计参数对空泡性能的影响研究[J]. 推进技术, 2019, 40(10): 2366-2372.

References

[1] Tulin M P. Supercavitation Flows-Small Pertubation Theory[J]. Journal of Ship Research， 1964，（4）: 16-36.
[2] 董世汤. 二元超空泡翼栅的自由流线理论[C]. 上海：中国造船学会年会， 1964.
[3] Geurse J A. Linearized Theory of Two-Dimensional Cavity Flows[D]. Delft: Delft University of Technology， 1961.
[4] Lee. Prediction of the Transient Cavitation on Marine Propellers by Numerical Lifting Surface Theory[C]. Tokyo: 13th Symposium on Naval Hydrodynamics， 1980.
[5] Kerwin J E， Lee C S. Prediction of Steady and Unsteady Marine Propeller Performance by Numerical Lifting-Surface Theory[C]. Jersey: Annual Meeting of Society of Naval Architects and Marine Engineers， 1978.
[6] Hess J L， Smith A M O. Calculation of Non-Lifting Potential Flow about Arbitrary Three Dimensional Bodies[J]. Journal of Ship Research， 1964， 8(2): 22-44.
[7] 熊鹰. 非均匀流中螺旋桨空泡及脉动压力的数值和试验研究[D]. 武汉: 武汉理工大学， 2002.
[8] 胡健. 螺旋桨空泡性能及低噪声螺旋桨性能研究[D]. 哈尔滨:哈尔滨工程大学， 2006.
[9] Gaggero S， Brizzolara S. A Potential Panel Method for the Prediction of Midchord Face and Back Cavitation[J]. Juounal of Fluids Engineering， 2001， 123(6): 311-319.
[10] Mitja Morgut， Enrico Nobile. Influence of the Mass Transfer Model on the Numerical Prediction of the Cavitation Flow Around a Marine Propeller[C]. Hamburg: Second International Symposium on Marine Propulsors， 2011.
[11] Dengcheng Liu. The CFD Analysis of Propeller Sheet Cavitation[C]. Nantes France: Proceedings of the 8th International Conference on Hydrodynamics， 2008.
[12] 温亮军，唐登海，辛公正，等. 螺旋桨设计参数对桨叶片空泡性能的影响分析[J]. 船舶力学， 2016， 20(11)： 1361-1368.
[13] 赵晓春，黄胜，王超，等. 螺旋桨自身参数对空泡性能的影响分析[J]. 应用科技， 2013， 40(12)， 24-33.
[14] 王超，熊鹰，何苗，等. 粒子群算法在大侧斜螺旋桨侧斜分布优化中的应用[J]. 上海交通大学学报， 2012， 46(3): 398-103.
[15] 王波，张以良，熊鹰. 船用螺旋桨水动力性能优化设计[J]. 武汉理工大学学报(交通科学与工程版)，2015， (4): 773-777.
[16] 饶志强，杨晨俊. 七叶侧斜螺旋桨水动力性能优化[J]. 中国造船. 2016， 57(4): 1-13.
[17] Brennen C E. Cavitation and Bubble Dynamics[M]. Oxford: Oxford University Press， 1995.
[18] Mishima S， Kinnas S A. Application of a Numerical Optimization Technique to the Desige of Cavitation Peopellers in Non-Uniform Flow[J]. Journal of Ship Research， 1997， 41(2): 93-107.
[19] Bertetta D， Brizzolara S， Gaggero S， et al. CPP Propeller Cavitation and Noise Optimization at Different Pitches with Panel Code and Validation by Cavitation Tunnel Measurements[J]. Ocean Engineering， 2012， 53(53): 177-195.
[20] Boswell R J. Design， Cavitation Performance and Open Water Performance of a Series of Research Skewed Propellers[R]. Bthesda: Department of the Naval Ship Research and Development Center， Report 3639， 1965.
[21] 朱德祥，张志荣，吴乘胜，等. 船舶CFD不确定度分析及ITTC临时规程的初步应用[J]. 水动力研究与进展， 2007， 22(3): 363-370.
[22] Kim S E. Multiphase CFD Simulation of Turbulent Cavitation Flows in and Around Marine Propuslors[R]. Carderock: David Taylor Model Basin， 1982.

Numerical Study on Effects of Design Parameters of Seven-Bladed Propeller with Skew on Its Cavitation Performance

七叶侧斜螺旋桨设计参数对空泡性能的影响研究

PDF

Knowledge

Abstract

Cite this article

share this article

References

Related Articles 0

Recommended Articles

Metrics

Comments